Numerical simulation of the bending stresses to varying loads in plastic gears

Authors

  • Jorge Laureano Moya Rodríguez Facultad de Mecánica, Universidad Central Marta Abreu de las Villas. Cuba
  • Tito Roberto Vílchez Vílchez Facultad de Ingeniería Mecánica, Universidad Nacional de Ingeniería. Lima, Perú.

DOI:

https://doi.org/10.21754/tecnia.v22i2.81

Keywords:

gears, numerical simulation, analytical calculation, MEF, bending

Abstract


The tests on test rigs to simulate the real contact conditions generated between the teeth of a gear, but are expensive and of limited utility for its accuracy depends on the condition of equipment and material. The objective of this research is to develop a procedure that simulates the bending stress in gear teeth plastic through numerical simulation method and the study of the main parameters that affect the performance of plastic gears such as torque, power and efforts of these gears when in operation regime, comparing with the molten steel. The results of this research meet the general and specific objectives of the study, which will help in improving the technology of Peruvian industry. 

Downloads

Download data is not yet available.

References

[1] ANSI/AGMA 1006-A97. Annex F. “Generating Gear Geometry without Racks”.
[2] Broersma, I., “Design of gears”. Editorial Industrial Press Inc., New York, 1975.
[3] Ashley, S., “Plastic Gears saves pounds and parts”. Revista Mechanical Engineering. May 1997, Vol 119, IIssue 5. ASME. USA.
[4] B., Turčič., “Technological Analysis of Using Polymer Materials for Gears”, report BMT 128/4/02, Prague, 15.9.2002.
[5] Kelley, J. W., “Polymers get in gears”. Revista Machine Design. Agosto 1996. Penton Publishing ISSN 0024-9114 USA.
[6] “Diagnosing Problems with plastic gears”. Revista Machine Design Julio 9, 1998. Penton Publishing ISSN 0024-9114 USA.
[7] Fitzinger, D., “Basic Training for designing Plastic gears”. Revista Machine Design. febrero 19, 1998. Penton Publishing ISSN 0024-9114 USA.
[8] Fritzinger, D., “What to put on parts prints of plastic gears. Revista Machine Design”. November 1998. Penton Publishing ISSN 0024-9114 USA.
[9] García, A., “Diseño de Moldes de inyección para la fabricación de Engranajes Plásticos Asimétricos”. Tesis presentada en Opción al Grado Académico de Master en Ciencias. Santa Clara. Cuba Noviembre del 2002.
[10] Kleiss, R., Hoffmann, S., “The Generation of Precision Spurs Gears Through Wire Electrical Discharge Machining”. Technical Conference of the American Gear Manufacturer's Association, 1993.
[11] Kleiss, R. E,, Kapelevich, A. L., Kleiss, Jr. N. J., “New Opportunities with Molded gears”, AGMA Fall Technical Meeting, Detroit, October 3-5, 2001, (01FTM9) Copyright _ 2001 American Gear Manufacturers Association 1500 King Street, Suite 201 Alexandria, Virginia, 22314 October, 2001 ISBN: 1--55589--788—6.
[12] Kleiss, R., Scott Hoffman, J., “The Generation of Precision Spur Gears Through Wire Electrical Discharge Machining”. 1993 Technical Conference of the AGMA.
[13] Kleiss, R., Must, E., “You Use Metal?”. Revista Design Engineering. Marzo 2001.
Rogers Media, Publishing. One Mount Pleasant Road, 7th Floor. Toronto, Ontario. Canada M5W 1A7.
[14] Kleiss, R., “The effect of thermal shrink and expansion on plastic gear geometry”. 1993 AGMA Conference on Gearing.

Downloads

Published

2012-12-01

How to Cite

[1]
J. L. Moya Rodríguez and T. R. Vílchez Vílchez, “Numerical simulation of the bending stresses to varying loads in plastic gears”, TECNIA, vol. 22, no. 2, pp. 45–53, Dec. 2012.

Issue

Vol. 22 No. 2 (2012)

Section

Articles

License

Copyright (c) 2012 TECNIA

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Articles published by TECNIA can be shared under the international Creative Commons license: CC BY 4.0. Permissions beyond this scope can be inquired via email at tecnia@uni.edu.pe.

Most read articles by the same author(s)